基于振动参数的钻井井架安全承载力评定

通过井架结构振动理论、有限元分析和实验室简易模型的试验研究，提出了以振动频率为基准，载荷下降系数为依据诊断钻井井架结构安全承载能力的方法。根据井架的具体结构形式和受力特征，将井架简化成一根沿长度上质量均匀分布、刚度恒定的简支梁，用振动理论推导出了井架固有频率的平方与作用载荷之间存在着线性关系，并通过有限元分析对这一关系进行了验证；提出了通过测试井架在两种不同栽荷作用下的固有频率推算井架临界承载并以此评定井架安全承载能力的方法；在实验室内制作了与A型井架相类似的模型，进行了逐级载荷下的固有频率测试，分析总结出适用于井架现场评定的具体方法，最后应用此方法对现场在役井架进行了测试与安全承载能力评定。该评定方法为井架测试、安全评定提供了一个新的发展方向，对保证钻井安全将起到重要的作用。     

A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

Development of a safety critical software requirements verification method with combined CPN and PVS: a nuclear power plant protection system application

Safety-critical software systems such as certain nuclear instrumentation and control (NI&C) systems should be developed with thorough verification. This study presents a method of software requirement verification with a case study for a nuclear power plant (NPP) protection system. The verification introduces colored petri net (CPN) for system modeling and prototype verification system (PVS) for mathematical verification. In order to aid flow-through from modeling by CPN to mathematical proof by PVS, an information extractor from CPN models has been developed in this paper. In order to convert the extracted information to the PVS specification language, a translator has also been developed. This combined method has been applied to the functional requirements of the Wolsong NPP Shut Down System #2 (SDS2); logical properties of the requirements were verified. Through this research, guidelines and a tool support for the use of formal methods have been developed for application to NI&C software verification.     

Development of core mode blocker with H/sub 2/-loaded Ge-B codoped fibres

A novel fabrication method of the core mode blocker by exposing H/sub 2/-loaded Ge-B codoped fibres to local electric arc discharge for application to the LPFGs-based tunable all-fibre bandpass filter with 6.5 nm bandwidth and 40 nm tuning range is presented.     

叠前地震数据优化处理技术分析

由于叠前时间偏移成像是在叠前数据上进行的，因此对数据的质量要求较高。针对这一问题进行了数据优化处理技术研究，研究的基础资料是胜利油田渤深6区块的三维地震数据，首先对资料的质量进行了分析一由于是拼接资料，因此存在着能量不均衡、覆盖次数不均匀、坡形不一致以及各类干扰发育等问题；然后针对这些问题研究了时间-空间域内分频随机噪声衰减、频率一空间域相干噪声衰减、波形匹配处理和数据拟合三维随机噪声衰减等4种处理方法，分别取得了很好的处理效果；在对实际资料进行数据优化处理时，根据资料的特点采用了合适的组合方式，处理后资料的品质得到了较大提高，相干噪声、随机噪声得到了有效衰减，波形一致性得到了恢复，中、深层有效频率和有效能量得到了加强。     

改性乳化沥青的发展和应用概况

综述了改性乳化沥青的发展及应用概况,重点讨论了改性乳化沥青的生产、制备工艺、稳定性影响因素,并对国内外改性乳化沥青的应用情况加以概述。     

混合动力电动汽车用电机及驱动控制器的电磁兼容设计

电机及驱动控制器作为电动汽车的关键部件,其电磁兼容设计对于保证电动汽车的可靠运行非常重要.介绍了国家十五项目中某混合动力轿车用电机及控制器系统的电磁兼容措施,分别从控制电路、信号电缆、功率电路及屏蔽机箱等工程角度进行了分析和设计.该系统的电磁兼容性符合GB/T17619-1998的要求,且已应用于实际混合动力电动汽车,运行情况良好.     

一种基于混沌同步的噪音衰减算法

论文提出了一种混沌通信系统的噪音衰减算法,该算法利用混沌同步现象在接收端获得正确的噪音估计值,从而从接收信号中滤除噪音恢复出正确的信号。通过数值仿真试验表明该方法是可行的。     

基于素性检验思想的不可约多项式判断

论文将Fermat素性检验的思想运用于不可约多项式的判断,给出了一个对于不可约判断问题的Monte Carlo 算法,分析了该算法的计算复杂度问题,并且给出了次数在200以内的检验结果。     

Acquisition and pattern recognition of spectrum information of welding metal transfer

With the creation of a pattern recognition system for metal transfer mode, this article has collected five kinds of spectrum signals in gas metal arc welding (MIG, MAG and CO₂) and take them as training samples. These samples have been pretreated by computer, several key characteristic parameters of the spectrum signal have been creatively extracted, and a corresponding recognition function and a minimum-distance-classifier have been constructed. The results show that the pattern recognition of several kinds of metal transfer modes for the metal gas arc welding can be done successfully, and relative important parameters in welding process, such as the frequency of droplet transfer and the approximate diameter of each droplet, can also be obtained.